'BLOCK MAGIC' Sealer - BLACK - ( Sample, 5 & 25 Litres) - Recolour to Your Old Block Paving to Make it Look Like New
HAVE A QUESTION?
Make Old Block Paving Look Like New
'Block Magic' will restore the colour and protect brick paving on driveways and patios
Smartseal 'Block Magic' is a formulation of UV resistant liquid pigments and acrylic sealing resins. It restores the original colour to old cobblelock driveways by penetrating into the block paving and replacing all the lost colour. One coat of 'Block Magic' followed by a 2nd coat of clear sealer will transforms all forms of block paving and leave sanded joints solid and resistant to weeds. 'Block Magic' is colour fast and guaranteed against colour loss for 5 years.
The colour restorer for cobblelock driveways can transform the look of your home by adding colour to the brick paving. UV light and general wear and tear can make cobblelock driveways and patios look old over time. Block Magic can transform the old brick paving to look like new.
- Restores colour to Block Paving
- Colour Fast and Stain Resistant
- Colour restorer for cobblelock driveways
- Durable sealer for driveways
- Adds Value to old drives and patios
- Inhibits algae and lichens that cause patio blackspot
- Also available in Red
See Technical section below for more information.
***Always apply to test area first***
Liquid UV stable pigments blended with acrylic resins and solvents create "block magic". Developed by Smartseal with older block paving in mind, it will not only recolour block paving but protect the paving from future colour loss, weeds algae and staining.
'Block Magic' Coloured Paving Sealer is applied by roller, at a rate of approx 3.0m2 per litre. Make sure the colour has dried evenly across the block paving before appying a clear second coat of sealer.Prior to applying sealer, sweep kiln dried sand into the joints and ideally compact with 'wacker plate'.The sealer will be tack free within 2 hours at 20°C and foot traffic may be permitted after 4 hours. Vehicles should be kept off the sealed area for a minimum of 24 hours at 20°C. These times may be increased or reduced depending on the ambient temperature.
Ensure no rain is forecast for at least 6 hours after application. Do not apply when the ground temperature is above 30°C or below 10°C.
All equipment should be cleaned with Smartseal cleaning fluid after use.
Deicing salts should not be applied directly on sealed block paving or concrete sealers.
Salt chemically reduces the temperature at which water freezes and will result in water ingress into the pavers.
Subsequent freezing may result in the paving 'sealer' being broken by the expansion of water as it freezes and white 'pitted' areas may become visible.
*****NOT TO BE USED ON CLAY PAVERS
Existing paving should be pressure washed to remove all surface debris and muck from the joints.
If the area is contaminated with weeds & moss then it should be treated with Smartseal moss clear or weed killer.
Oil and other stains should be removed using Smartseal Driveway Cleaner or Oil Remover.
The treated area should then be left to dry and the joints re-sanded & compacted to the lower edge of the paver chamfers with clean kiln-dried sand.
Moisture in the paver & sand will inhibit penetration of the sealer and produce whiteness.
Technical & Test Data
Smartseal Block Paving sealer has been tested by the TRL (Transport Research Laboratory) and certified that it meets the SRV (Skid Resistance Value) for all categories of paving for local authority pedestrian areas and when heavily trafficked is suitable for special applications where risks of skidding are high as laid down in the UK Highway Authorities Tender Specification. Copies available on request.
"Newly laid block paving shall be treated with Smartseal block paving sealer to protect and stabilise jointing sand and enhance surface colour and increase abrasion resistance.
All materials should comply with ISO9002 for Quality Assurance.
All work should be carried out in conjunction with the manufacturer's current technical data sheet and instructions for use".
Health & Safety
Flammable liquid. Do not smoke. Keep application area well ventilated.
Wear respirator, gloves and goggles when applying. Store in a cool place. Flash point 40°C (Abel-Closed Cup). Refer to the Health & Safety Data Sheet for further information.